时间:12-14阅读次数:441责任编辑:远航 所属栏目:卡箍式橡胶接头
导读:左贡县是西藏自治区昌都市的下辖县,位于西藏自治区东南部,昌都市东南部。地处东经97°06′-98°36′、北纬28°30′-30°28′。东与芒康县接
左贡县是西藏自治区昌都市的下辖县,位于西藏自治区东南部,昌都市东南部。地处东经97°06′-98°36′、北纬28°30′-30°28′。东与芒康县接壤,南与林芝市察隅县相连,西与八宿县毗邻,北与察雅县隔江相望。属藏东南高原温带半干旱气候。县域东西很大距离为408公里,南北很大距离为220公里。总面积1.17万平方公里,辖3个镇、7个乡,127个行政村、1个居委会,总人口45852人(2014年)。县人民驻旺达镇,县城距拉萨1067公里。左贡藏语意为“偏(耕)牛背”的意思。左贡县境内主要山脉有东达山、多拉山、茶瓦珠山、茶瓦多吉志嘎山
公称通径DN Nominal Diameter (mm) |
长度 LengthLmm |
轴向位移 Axial displacement mm |
横向位移 Haorizontal isplacement mm |
偏转角度 Angular deflection(a1+a2)° |
||
mm |
英寸inch |
伸长Extension | 压缩Compression | |||
32 | 1.25 | 95 | 6 | 9 | 9 | 15 |
40 | 1.5 | 95 | 6 | 10 | 9 | 15 |
50 | 2 | 105 | 7 | 10 | 10 | 15 |
65 | 2.5 | 115 | 7 | 13 | 11 | 15 |
80 | 3 | 135 | 8 | 15 | 12 | 15 |
100 | 4 | 150 | 10 | 19 | 13 | 15 |
125 | 5 | 165 | 12 | 19 | 13 | 15 |
150 | 6 | 180 | 12 | 20 | 14 | 15 |
200 | 8 | 210 | 16 | 25 | 22 | 15 |
250 | 10 | 230 | 16 | 25 | 22 | 15 |
300 | 12 | 245 | 16 | 25 | 22 | 15 |
350 | 14 | 255 | 16 | 25 | 22 | 15 |
400 | 16 | 255 | 16 | 25 | 22 | 15 |
450 | 18 | 255 | 16 | 25 | 22 | 15 |
500 | 20 | 255-320 | 16 | 25 | 22 | 15 |
600 | 24 | 260-350 | 16 | 25 | 22 | 15 |
700 | 28 | 260-350 | 16 | 25 | 22 | 15 |
800 | 32 | 260-350 | 16 | 25 | 22 | 15 |
900 | 36 | 260-350 | 16 | 25 | 22 | 15 |
1000 | 40 | 260-350 | 18 | 26 | 24 | 15 |
1200 | 48 | 260-550 | 18 | 26 | 24 | 15 |
1400 | 56 | 350-550 | 20 | 28 | 26 | 15 |
1500 | 60 | 350-550 | 20 | 28 | 26 | 15 |
1600 | 64 | 350-550 | 25 | 35 | 30 | 10 |
1800 | 72 | 350-550 | 25 | 35 | 30 | 10 |
2000 | 80 | 350-550 | 25 | 35 | 30 | 10 |
2200 | 88 | 400-550 | 25 | 35 | 30 | 10 |
2400 | 96 | 400-550 | 25 | 35 | 30 | 10 |
2600 | 104 | 400-550 | 25 | 35 | 30 | 10 |
2800 | 112 | 400-550 | 25 | 35 | 30 | 10 |
3000 | 120 | 400-500 | 25 | 35 | 30 | 10 |
3200 | 120 | 400-500 | 25 | 35 | 30 | 10 |
3400 | 120 | 400-500 | 25 | 35 | 30 | 10 |
3600 | 120 | 400-500 | 25 | 35 | 30 | 10 |
3800 | 120 | 400-500 | 25 | 35 | 30 | 10 |
4000 | 120 | 400-500 | 25 | 35 | 30 | 10 |
注:1、特殊要求可按用户图纸制作,法兰标准采用9115.1-2000,可选配(GB、JB、HG、CB、ANSI、DIN、BSEN、NF、EN、JIS、 等)法兰标准生产。橡胶球体可做天然橡胶、三元乙丙橡胶、氯丁橡胶、丁基橡胶、丁腈橡胶、氟橡胶等。 2、悬空给水使用DN200以上产品,管道必须有固定支撑或固定托架,否则产品应安装防拉脱装置。 3、用户使用橡胶接头,对应法兰应是阀门法兰或符合9115.1-2000法兰。 Notes:1. For OEM orders with special requirement, rubber joints can be made according to customers' drawings. Generally, flange standard is 9115.1-2000, other GB, JB, HG, CB, ANSI, DIN, BSEN, NF, EN, JIS, flanges are also available upon request. Material of rubber body can be NR natural rubber, EPDM, Neoprene, IIR butyl rubber, NBR Buna-N, FKM, etc. 2.When rubber joints size above DN200 are used for overhead water supply system, the pipes must be equipped with fixed supports or fixed brackets, otherwise control units shall be installed on rubber joints. 3.Matching flanges of rubber joints shall be valve flanges or 9115.1-2000 flanges. |
热度新闻
随便看看